30.5x30.5mm Holybro KAKUTE H7 v1.3 Tekko32 F4 Metal 4in1 65A ESC Stack Flight Controller 5V 9V BEC / Atlatl HV V2 0.5/ 25/ 200/ 500/ 800mW VTX for RC Drone FPV Racing

LOCKPICKWEBSKU: Holybro KAKUTE-NO VTX-01

Version: NO VTX
Price:
$172.99

Tax included Shipping calculated at checkout

Stock:
In stock

Description

Specification:

Brand: Holybro

Model:  KAKUTE H7 V1.3 Tekko32 F4 4in1 65A ESC Stack

Optional Version: NO VTX / With VTX

Kakute H7 V1.3

( Manual)
 

MCU: STM32H743 32-bit processor running at 480 MHz
IMU: MPU6000
Barometer: BMP280
OSD: AT7456E
Onboard Bluetooth chip: ESP32-C3
SpeedyBee IOS & Android App Compatible
Note: The Bluetooth onboard is set to automatically turn off when the flight controller is unlocked (arm) ,

and turn on automatically when the flight controller is locked (disarm).
6x UARTs (1,2,3,4,6,7; UART2 is used for Bluetooth telemetry)
9x PWM Outputs (8 Motor Output, 1 LED)
2x JST-SH1.0 8pin ESC port (4in1 ESCs, x8/Octocopter compatible)
1x JST-SH1.0 6pin VTX port (For HD System like Caddx Vista & Air Unit)
Battery input voltage: 7V to 42V
BEC 5V 2A Cont.
BEC 9V 3A Cont
USB Type-C
Mounting: 30.5 x 30.5mm/Φ4mm hole with Φ3mm Grommets
Dimension: 35x35mm
Weight: 8g

Firmware:

BetaFlight: KakuteH7 (v4.2.11 and above)
INAV: KakuteH7 (4.0.0 & above) SD card support added in 4.1.0.
ArduPilot: KakuteH7 (4.2.0 & above)

Tekko32 F4 Metal 4in1 65A ESC

( Pin Cable)
 

Continuous Current: 65A x4
Burst Current: 75A x4
Supports 4-6S battery
Supports DShot 150/300/600/1200 & MultiShot/OneShot/Proshot/PWM etc.
ESC telemetry Supported
Onboard analog current sensor
No output BEC
BLHeli_32 firmware
1000uf 35v capacitor included (highly recommended for 6s setup)
Amperage meter scale ratio: 180 
Dimensions: 43 x 44mm / Weight: 15.8g
Mounting holes: M4 30.5x30.5mm (M3 grommets included)

 

Features:

New & faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0 @48Mhz)
PWM Frequency: 16k to 96k
Metal-cased MOSFET for excellent heat dissipation
Massive on-board capacitance for noise filtering at 2068uf
3 oz copper PCB design to allow bigger current and better heat dissipation
Separate drive & control circuit, 

this broadens the current capability of the drive circuit while reducing the electrical interference to the control circuit.

NO VTX Version without VTX Module

With VTX Version

( Manual)

Model: Atlatl HV V2 VTX

Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
Audio: 6.5 MHz Mono
Protocol?smart audio2.0
Antenna Connector: MMCX
Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
Dimensions: 35x25x7mm (Includes USB height)
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 9.3g

( VTX Table Link )


Package Included:

NO VTX Version

1x Kakute H7 v1.3 FC

1x Tekko32 F4 Metal 4in1 65A ESC
1x Electrolytic capacito: 1000uF 35v 
1x  8pin to 8pin 1mm pitch 65mm cable
1x  8pin to 8pin 1mm pitch 25mm cable
1x  JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x  JST SH 6pin 100mm cable(for Caddx HD Systems)

with VTX Version

1x Kakute H7 v1.3 FC

1x Tekko32 F4 Metal 4in1 65A ESC

1x Atlatl HV V2 VTX

1x Electrolytic capacito: 1000uF 35v 
1x 8pin to 8pin 1mm pitch 65mm cable
1x 8pin to 8pin 1mm pitch 25mm cable
1x JST SH 6pin to JST GHR 8pin 80mm &150mm cable (for DJI/Caddx HD System)
1x JST SH 6pin 100mm cable(for Caddx HD Systems)
1x 80mm SMA–MMCX Cable
1x JST GHR 4pin 150mm cable

 

 

 

 

Payment & Security

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently viewed