100kHz-350MHz 2.8 Inch Handheld Two Inputs Tiny Spectrum Analyzer Touch Screen Spectrum Analyzer 100 KHz-350MHz Input Frequency

SKU: Spectrum Analyzer-100kHz-350MHz

Price:
$77.99

Tax included Shipping calculated at checkout

Stock:
In stock

Description

Features:

  • Display resolution 320 * 240 pixels

  • 2.8 inches diagonal screen

  • 16 bits per RGB pixel

  • Resistive touch control

  • Slow switch control

  • USB serial port control

  • Optional TTL USART port on the internal PCB (SW not yet implemented)

  • Linear power supply to avoid switching noise

  • TinySA's input/output specifications are divided into 4 modes

Specifications:

Low input mode specification:
*And input frequency response from 100kHz to 350MHz
*When the input impedance is set to 10dB or higher, it is 50 ohms.
*So optional manual and automatic input attenuation, the range is 0dB to 31dB, the step size is 1 dB
*Then absolute maximum input level, no attenuation + 10dBm
*Absolute maximum power, 30dB attenuation + 20dBm in a short time
*With a third-order modulation product (IIP3) input intercept point 0dB attenuation + 15dBm
* 1dB compression point, + 2dBm attenuation 0dB
*The resolution of the power detector is 0.5dB, linearity and frequency are +/- 1dB
*The absolute power level accuracy after power level calibration is +/- 1dB
*The lowest resolvable signal with a resolution bandwidth of -102dBm and a resolution of 30kHz
*The frequency accuracy is equal to the selected resolution bandwidth
*Phase noise is -90dB/Hz at 100kHz offset and -115dB/Hz at 1MHz offset
*Use 30kHz resolution bandwidth to 70dB
*The manually selected resolution filter is 3, 10, 30, 100, 300, 600kHz. One of 57 resolution filters is automatically selected.
*The screen resolution is 145 or 290 measuring points.
*Using the maximum resolution filter, so the scanning speed exceeds 1000 points per second.
*Automatically optimize the actual scan point to cover the entire scan range, regardless of the selected resolution bandwidth
*The spurious suppression option is used to determine whether certain signals are generated internally or actually exist in the input signal.
 
High input mode specification:

*The input frequency range is 240MHz to 960MHz

*If there is no input band filter to filter out strong signals outside the range of 240MHz to 960MHz, so it may cause distortion. So in-band signal

*Absolute maximum input level, so no attenuation + 10dBm

*The input intercept point of the third-order modulation product (IIP3) -5dBm

* 1dB compression point at -6dBm,so attenuation is 0dB

*The resolution of the power detector is 0.5dB,then linearity and frequency +/-1dB

*The absolute power level accuracy after power level calibration is +/- 1dB

*The lowest visible signal with a resolution bandwidth of -115dBm 30kHz

*The frequency accuracy is equal to the selected resolution bandwidth

*Use 30kHz resolution bandwidth 50dB spurious-free dynamic range

*Optional 3, 10, 30, 100, 300 and 600kHz

* Optional 25dB to 40dB frequency-related input attenuator. The power level error of the activated attenuator is increased to +/- 15dB

*The screen resolution is 145 or 290 measuring points.

*Using the maximum resolution filter, so the scanning speed exceeds 1000 points per second.

*Automatically optimize the actual scan point to cover the entire scan range, regardless of the selected resolution bandwidth

 It can help people's lives more convenient, and it is cheap, and it is cheap enough that more and more people can use it.Although it is cheap but its quality is not bad at all, this product helps a lot of people to solve their life troubles

Low output mode specification:

*Sine output, harmonics are lower than the fundamental -40dB

*The output frequency range is 100kHz to 350MHz

* Optional AM, narrow FM and wide FM modulation or sweep slowly in the selectable frequency range

 

High output mode specifications:

*Square wave output

*The output frequency range is 240MHz to 960MHz

*Optional narrow FM and wide FM modulation or slow sweep in the selectable frequency range

 

Reference generator specifications:

*Optional square wave output, basically connected to high input/output at -25dBm

*The frequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz.

 

Battery specifications:

*The charging time is up to 1 hour under at least 500mA USB port or USB charger

* Run for at least 2 hours on a fully charged battery

 

Package included:

1 x Spectrum analyzer

1 x Antenna

2 x Cable

1 x USB data cable

 

Details pictures: 

 

Payment & Security

Payment methods

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.


Security

Estimate shipping

You may also like

Recently viewed